Virginia Regulatory Town Hall

Final Text

highlight

Action:
Motor Vehicle Safety Inspection Rules and Regulations - Fall ...
Stage: Final
 
19VAC30-70-50

19VAC30-70-50. Approval stickers and decals.

A. If the vehicle meets all inspection requirements, the certified safety inspector performing the inspection shall immediately enter the receipt information via the MVIP system.

The inspection sticker is not valid unless the rear portion is completed with the vehicle make, year built, license plate number (dealer name if a dealer tag is displayed), body type, and the complete vehicle identification number (VIN). The inspection sticker shall be completed using black indelible ink.

B. Approval stickers and decals shall be issued according to the following schedule:

ANNUAL PROGRAM

Vehicles inspected in January are issued stickers bearing the Number "1"
Vehicles inspected in February are issued stickers bearing the Number "2"
Vehicles inspected in March are issued stickers bearing the Number "3"
Vehicles inspected in April are issued stickers bearing the Number "4"
Vehicles inspected in May are issued stickers bearing the Number "5"
Vehicles inspected in June are issued stickers bearing the Number "6"
Vehicles inspected in July are issued stickers bearing the Number "7"
Vehicles inspected in August are issued stickers bearing the Number "8"
Vehicles inspected in September are issued stickers bearing the Number "9"
Vehicles inspected in October are issued stickers bearing the Number "10"
Vehicles inspected in November are issued stickers bearing the Number "11"
Vehicles inspected in December are issued stickers bearing the Number "12"

All February annual inspection stickers for trailer and motorcycle decals (#2) due to expire at midnight, February 28 automatically will be valid through midnight February 29 each leap year.

C. The numeral decal indicating the month of expiration shall be inserted in the box identified as month and the numeral decal indicating the year of expiration shall be inserted in the box identified as year of the approval sticker and the trailer or motorcycle sticker. Extreme care should be used by inspectors in applying these inserts. On all windshields, except school buses, the sticker is to be placed at the bottom left corner of the windshield so that the inside or when viewed from the inside of the vehicle. The left edge of the sticker is to be placed as close as practical, but no closer than one inch to the right of the vertical center left edge of the windshield when looking through the windshield from viewed from the inside of the vehicle. (If the vehicle is normally operated from the right side, the sticker must be placed one inch to the left of the vertical center of the windshield.) The top edge of the sticker is to be approximately four inches from the bottom of the windshield when viewed from the inside of the vehicle.

On passenger vehicles not equipped with a windshield, the sticker shall be placed on or under the dash and protected in some manner from the weather.

The approval sticker on official yellow school buses is to be placed at the bottom and in the right corner of the windshield when looking through the windshield from inside the vehicle.

EXCEPTIONS: The approval sticker shall be placed one inch to the right of the vertical center of the windshield when looking through the windshield from the inside on all new flat-face cowl yellow school buses. On vehicles equipped with heating and grid elements on the inside of the windshield, the sticker shall be placed one inch above the top of the grid element and the inside left edge of the sticker shall be approximately one inch to the right of the vertical center left edge of the windshield when looking through the windshield from the inside viewed from the inside of the vehicle.

Stickers or decals used by counties, cities and towns in lieu of license plates affixed adjacent to the old approval sticker and which are affixed in the location where the new approval sticker is required to be placed will not be removed. Any sticker or decal required by the laws of any other state or the District of Columbia and displayed upon the windshield of a vehicle submitted for inspection in the Commonwealth is permitted by the superintendent, provided the vehicle is currently registered in that jurisdiction, and the sticker is displayed in a manner designated by the issuing authority and has not expired. In these cases, the approval if the sticker or decal is located where the inspection sticker is to be placed, it will not be removed unless the owner or operator authorizes its removal. The inspection sticker will be placed as close to one 1/4 inch to the right of the vertical center of the windshield as it can be placed sticker or decal when viewed from the inside of the vehicle without removing or overlapping the county, city or town sticker or decal.

D. The Code of Virginia requires that the inspection sticker be displayed on the windshield or at other designated places at all times. The inspection sticker cannot be transferred from one vehicle to another.

EXCEPTION: If the windshield in a vehicle is replaced, a valid sticker may be removed from the old windshield and placed on the new windshield.

E. The sticker issued to a motorcycle shall be affixed to the left side of the cycle where it will be most visible after mounting. The sticker may be placed on a plate on the left side where it will be most visible and securely fastened to the motorcycle for the purpose of displaying the sticker. The sticker may be placed horizontally or vertically.

F. Trailer stickers will be issued to all trailers and semitrailers required to be inspected. (No boat, utility, or travel trailer that is not equipped with brakes shall be required to be inspected.)

G. All inspected trailers must display a trailer sticker on that particular vehicle. These stickers are to be placed on the left side of the trailer near the front corner. The sticker must be affixed to the trailer body or frame. In those instances where a metal back container with a removable transparent cover has been permanently affixed to the trailer body, the sticker may be glued to it. The container must be permanently mounted in such a manner that the sticker must be destroyed to remove it.

H. In all other cases involving unusually designed trailers such as pole trailers, the safety inspector is to exercise his own good judgment in placing the sticker at a point where it will be as prominent as possible and visible for examination from the left side.

I. Motorcycles have a separate sticker that is orange and issued with the prefix M. Trailers have a separate sticker that is blue and issued with the prefix T. The trailer and motorcycle receipts are completed in the same manner as other inspection receipts.

J. Appointed stations will keep sufficient inspection supplies on hand to meet their needs. Requests for additional supplies shall be ordered via the MVIP system. Requests for supplies that are to be picked up at the Safety Division Headquarters must be made at least 24 hours prior to pick up.

Packing slips mailed with inspection supplies will be kept on file at the station for at least 24 months.

K. All unused center inserts used to indicate the month that a sticker expires, in possession of the inspection station at the end of each month, shall be retained by the inspection station, properly safeguarded, and used in the inspection of vehicles for that particular month in the following year or be disposed of as directed by the Department of State Police.

All inspection supplies that are voided, damaged, disfigured or become unserviceable in any manner, will be returned to the Safety Division. New replacement supplies will be issued to the station. Expired stickers will be picked up by the station's supervising trooper.

L. All voided approval or rejection stickers will be picked up by the station's supervising trooper.

M. The MVIP system approval or rejection printed receipt shall be given to the owner or operator of the vehicle.

N. All yellow receipt copies of approval stickers and decals will be retained in the books and shall be kept on file at the station for at least six months. They may be inspected by any law-enforcement officer during normal business hours.

O. Safety Division troopers may replace inspection stickers that have separated from the windshield of motor vehicles and become lost or damaged without conducting an inspection of the safety components of the vehicle. Such replacement of inspection stickers shall be made only in accordance with the following provisions:

1. A vehicle owner or operator complaining of the loss or damage to the inspection sticker on the windshield of their vehicle due to separation of the sticker from the windshield shall be directed to the nearest Safety Division Area Office or Safety Division trooper.

2. Safety Division troopers, upon receipt of a complaint from a vehicle owner or operator that their inspection sticker has been stolen, lost or become damaged due to separation from the windshield, will make arrangements to meet the person to effect the replacement of the sticker. A vehicle owner or operator alleging theft of the inspection sticker will furnish proof to the Safety Division trooper that such theft has been reported to the proper law-enforcement authority.

3. The vehicle owner or operator must produce the original safety inspection approval sticker receipt indicating a valid approval inspection sticker was issued to the vehicle within the past 11 months. (The vehicle must be reinspected if the expiration of the original inspection sticker is in the month the request is being made.)

4. The Safety Division trooper will verify by the inspection receipt that the vehicle was issued an approval inspection sticker within the past 11 months and will then issue a replacement inspection sticker to the vehicle. If any obvious equipment defects are detected during the replacement process, the vehicle will not be issued a replacement approval sticker.

5. The Safety Division trooper will complete the inspection sticker receipt for the approval sticker from information contained on the original receipt. The date the replacement sticker is issued will be used in the date space. In the space for Inspection Related Charges, the trooper will insert the word "REPLACEMENT" and the sticker number from the original inspection receipt.

6. The Safety Division trooper will sign the receipt vertically in the O.K. column in the "Equipment Inspected" blocks. These blocks will not otherwise be completed.

7. The Safety Division trooper shall place month and year inserts on the inspection sticker to reflect the expiration as shown on the original approval inspection sticker and place the inspection sticker on the windshield in accordance with the requirements of subsection C of this section.

8. The Safety Division trooper will enter the replacement information into the MVIP system.

P. New vehicle safety inspections.

1. Section 46.2-1158.01 of the Code of Virginia allows an employee who customarily performs the inspection requirement of a manufacturer or distributor of new motor vehicles to place an inspection sticker furnished by the Department of State Police on the vehicle once it has met the requirements of that manufacturer or distributor. This employee does not have to be a certified safety inspector.

2. With the addition of other personnel using Department of State Police inspection supplies, a system shall be developed at each inspection station to afford accountability of all supplies. The system shall include proper safeguards to prevent the loss of supplies through carelessness, neglect, theft, or unauthorized use.

3. Inspection stations shall not mix annual state inspections with predelivery inspections (PDI) in the same book of inspection stickers.

4. All employees shall be reminded that anyone who performs inspections, whether it be for the annual inspection or the PDI inspection, is subject to criminal prosecution if inspection supplies are used illegally or used in some other unauthorized way.

5. Station management and licensed safety inspectors are subject to administrative sanctions for any misuse of inspection supplies.

6. The inspection receipts shall be completed as usual with the following exceptions: On the "inspector" line, the initials "PDI" (for predelivery inspection) and the printed employee's name performing the inspection shall be entered. On the "inspector's license number" line, the letters "N/A" shall be entered. In the equipment inspected section, the words "New Vehicle" shall be entered in the "adjust" column. The PDI employee performing the inspection shall sign his name in the "O.K." column.

19VAC30-70-210

19VAC30-70-210. Glass and glazing.

A. Motor vehicles may be inspected without windshields, side glasses, or any kind of glazing, except that any motor vehicle other than a motorcycle that was manufactured, assembled, or reconstructed after July 1, 1970, must be equipped with a windshield. If glass or other glazing is installed, it must be inspected. If no windshield is installed, see 19VAC30-70-50 C for location of the sticker.

B. Inspect for and reject if:

1. Any motor vehicle manufactured or assembled after January 1, 1936, or any bus, taxicab or school bus manufactured or assembled after January 1, 1935, is not equipped throughout with safety glass, or other safety glazing material. (This requirement includes slide-in campers used on pickups or trucks, caps, or covers used on pickup trucks, motor homes, and vans.)

2. Any safety glass or glazing used in a motor vehicle is not of an approved type and properly identified (refer to approved equipment section). (Replacement safety glass installed in any part of a vehicle other than the windshield need not bear a trademark or name, provided the glass consists of two or more sheets of glass separated by a glazing material, and provided the glass is cut from a piece of approved safety glass, and provided the edge of the glass can be observed.)

NOTE: A number of 1998 and 1999 model year Ford Contour/Mystique, Econoline and Ranger vehicles were produced without the AS-1 windshield marking as required by FMVSS #205. Ford has certified that these vehicles' windshields meet all performance standards and will not be rejected.

3. Any glass at any location where glass is used is cracked or broken so that it is likely to cut or injure a person in the vehicle.

4. Windshield has any cloudiness more than three inches above the bottom, one inch inward from the outer borders, one inch down from the top, or one inch inward from the center strip. The bottom of the windshield shall be defined as the point where the top of the dash contacts the windshield.

5. Any distortion or obstruction that interferes with a driver's vision; any alteration that has been made to a vehicle that obstructs the driver's clear view through the windshield. This may include but is not limited to large objects hanging from the inside mirror, CB radios or tachometers on the dash, hood scoops, and other ornamentation on or in front of the hood that is not transparent.

a. Any hood scoop installed on any motor vehicle manufactured for the year 1990 or earlier model year cannot exceed 2-1/4 inches high at its highest point measured from the junction of the dashboard and the windshield.

b. Any hood scoop installed on any motor vehicle manufactured for the 1991 or subsequent model year cannot exceed 1-1/8 inches high at its highest point measured from the junction of the dashboard and the windshield.

6. Windshield glass, on the driver's side, has any scratch more than 1/4 inch in width and six inches long within the area covered by the windshield wiper blade, excluding the three inches above the bottom of the windshield. A windshield wiper that remains parked within the driver's side windshield wiper area shall be rejected.

EXCEPTION: Do not reject safety grooves designed to clean wiper blades if the grooves do not extend upward from the bottom of the windshield more than six inches at the highest point.

7. There is a pit, chip, or star crack larger than 1-1/2 inches in diameter at any location in the windshield above the three-inch line at the bottom.

8. At any location in the windshield above the three-inch line at the bottom (as measured from the junction of the dash board and the windshield) there is more than one crack from the same point if at least one of the cracks is more than 1-1/2 inches in length. There is any crack that weakens the windshield so that one piece may be moved in relation to the other. (If there is more than one crack running from a star crack that extends above the three-inch line, the windshield shall be rejected.)

EXCEPTION: Windshield repair is a viable option to windshield replacement. A windshield that has been repaired will pass inspection unless:

a. It is likely to cut or injure a person.

b. There is any distortion that interferes with a driver's vision.

c. The windshield remains weakened so that one piece may be moved in relation to the other.

d. The integrity of the windshield has obviously been compromised by the damage or the repair.

9. Any sticker is on the windshield other than an official one required by law or permitted by the superintendent. Authorization is hereby granted for stickers or decals, to include those required by any county, town, or city, measuring not more than 2-1/2 inches in width and four inches in length to be placed in the blind spot behind the rear view mirror. Department of Defense decals measuring no more than three inches in width and eight inches in length may be affixed to the upper edge of the center of the windshield. At the option of the motor vehicle's owner, the decal may be affixed at the lower left corner of the windshield so that the inside or left edge of the sticker or decal is within one inch of the extreme left edge of the windshield when looking through the windshield from inside the vehicle. When placed at this location, the bottom edge of the sticker or decal must be affixed within three inches of the bottom of the windshield. This location can only be used if the owner of the vehicle has chosen not to place any required county, town or city decal there. The normal location for any required county, town, or city decal sticker is adjacent to the right side of the official inspection sticker and must not extend upward more than three inches from the bottom of the windshield when viewed from inside the vehicle. The top edge of the sticker is to be approximately four inches from the bottom of the windshield. The left side edge adjacent to the official inspection sticker shall not be more than 1/4 inch from the right edge of the official inspection sticker when viewed from inside the vehicle. Valid Commercial Vehicle Safety Alliance (CVSA) inspection decals or similar commercial vehicle inspection decal issued by local law enforcement may be placed at the bottom or sides right corner of the windshield provided when viewed from inside the vehicle. The top edge of such decals do not extend more than 4-1/2 are to be approximately four inches from the bottom of the windshield when viewed from inside the vehicle and are to be located outside the area swept by the windshield wipers and outside the driver's sight line.

Any sticker or decal required by the laws of any other state or the District of Columbia and displayed upon the windshield of a vehicle submitted for inspection in this state is permitted by the superintendent, provided the vehicle is currently registered in that jurisdiction, and the sticker is displayed in a manner designated by the issuing authority and has not expired. This includes vehicles with dual registration; (i.e., Virginia and the District of Columbia).

NOTE: Any Virginia registered vehicle displaying a valid sticker or decal required by a county, town, or city is permitted by the superintendent to remain in its current location through December 31, 2018, unless such location conflicts with the inspection sticker placement. This provision will afford localities time to enact changes to regulations governing required stickers or decals that may be impacted by the 2018 inspection sticker placement change.

NOTE: Fastoll Transponder Toll transponder devices may be affixed to the inside center of the windshield at the roof line just above the rear view mirror. If space does not allow, then it the transponder device may be affixed to the immediate right of the mirror at the roof line.

NOTE: Volvo placed a warning sticker on the windshield of their cars equipped with side impact air bags. In accordance with this paragraph the sticker shall be removed. If the sticker can be removed intact then it may be placed on the left rear window in the lower front corner. Customers should be referred to the nearest Safety Division area office for replacement if it could not be removed intact.

NOTE: A licensed motor vehicle dealer may apply one transponder sticker no larger than one inch by four inches and one barcode sticker no larger than three inches by four inches to the driver's side edge of a vehicle's windshield to be removed upon the sale or lease of the vehicle provided that it does not extend below the AS-1 line. In the absence of an AS-1 line the sticker cannot extend more than three inches downward from the top of the windshield.

EXCEPTION: Stickers or decals used by counties, cities and towns in lieu of license plates may be placed on the windshield without further authority. Except on privately owned yellow school buses, the sticker or decal shall be placed on the windshield adjacent to the right side of the official inspection sticker or the optional placement to the extreme lower left side of the windshield. The top edge of the sticker or decal shall not extend upward more than three inches from the bottom of the windshield. The left side edge adjacent to the official inspection sticker shall not be more than 1/4 inch from the right edge of the official inspection sticker when looking through the windshield from inside the vehicle. At the option of the motor vehicle owner, the sticker or decal may be affixed at the lower left corner of the windshield so that the inside or left edge of the sticker or decal is within one inch of the extreme left edge of the windshield when looking through the windshield from inside the vehicle. When placed at this location, the bottom edge of the sticker or decal must be affixed within three inches of the bottom of the windshield.

NOTE: Any vehicle displaying an expired sticker or decal on its windshield at the time of inspection, excluding a rejection sticker that is present on the windshield at the time of inspection, shall not be issued an approval sticker unless the owner/operator "authorizes" owner or operator authorizes its removal. A rejection sticker will be issued versus an involuntary removal. On privately owned yellow school buses, the sticker or decal shall be placed on the windshield adjacent to the left side of the official inspection sticker, and not more than 1/4 inch from the left edge of the official inspection sticker when looking through the windshield from inside the vehicle. The top edge of the sticker shall not extend upward more than three inches from the bottom of the windshield.

10. Sunshading material on the windshield, or words, lettering, numbers or pictures that does do not extend below the AS-1 line will not be considered for inspection. In the absence of an AS-1 line sunshading material on the windshield displaying words, lettering, numbers or pictures cannot extend more than three inches downward from the top of the windshield, unless authorized by the Virginia Department of Motor Vehicles and indicated on the vehicle registration.

NOTE: Vehicles with logos made into the glass at the factory meet federal standards and will pass state inspection.

11. Any sunscreening material is scratched, distorted, wrinkled or obscures or distorts clear vision through the glazing.

12. Front side windows have cloudiness above three inches from the bottom of the glass or other defects that affect the driver's vision or one or more cracks which that permit one part of the glass to be moved in relation to another part. Wind silencers, breezes or other ventilator adaptors are not made of clear transparent material.

EXCEPTION: Colored or tinted ventvisors that do not exceed more than two inches from the forward door post into the driver's viewing area are permitted.

13. Glass in the left front door cannot be lowered so a hand signal can be given. (This does not apply to vehicles that were not designed and/or or manufactured for the left front glass to be lowered, provided the vehicle is equipped with approved turn signals.) If either front door has the glass removed and material inserted in place of the glass that could obstruct the driver's vision.

EXCEPTION: Sunscreening material is permissible if the vehicle is equipped with a mirror on each side.

14. Any sticker or other obstruction is on either front side window, rear side windows, or rear windows. (The price label, fuel economy label and the buyer's guide required by federal statute and regulations to be affixed to new/used new or used vehicles by the manufacturer shall normally be affixed to one of the rear side windows.) If a vehicle only has two door windows, the labels may be affixed to one of these windows. If a vehicle does not have any door or side windows the labels may be temporarily affixed to the right side of the windshield until the vehicle is sold to the first purchaser.

NOTE: A single sticker no larger than 20 square inches in area, if such sticker is totally contained within the lower five inches of the glass in the rear window if a vehicle has only one outside mirror, a single sticker or decal no larger than 10 square inches located in an area not more than three inches above the bottom and not more than eight inches from the rearmost edge of either front side window, is permissible and should not be rejected.

A single sticker issued by the Department of Transportation to identify a physically challenged driver, no larger than two inches by two inches, located not more than one inch to the rear of the front door post, or one inch to the rear of the front ventilator glass, if equipped with a ventilator glass, and no higher than one inch from the bottom of the window opening, is permitted on the front driver's side window on a vehicle specially equipped for the physically challenged.

15. Rear window is clouded or distorted so that the driver does not have a view 200 feet to the rear.

EXCEPTIONS: The following are permissible if the vehicle is equipped with a mirror on each side:

a. There is attached to one rear window of such motor vehicle one optically grooved clear plastic right angle rear view lens, not exceeding 18 inches in diameter in the case of a circular lens or not exceeding 11 inches by 14 inches in the case of a rectangular lens, which enables the operator of the motor vehicle to view below the line of sight as viewed through the rear window.

b. There is affixed to the rear side windows, rear window, or windows of such motor vehicle any sticker or stickers, regardless of size.

c. There is affixed to the rear side windows, rear window, or windows of such motor vehicle a single layer of sunshading material.

d. Rear side windows, rear window, or windows is clouded or distorted.